SPECIFICATIONS

Product specification:

This is a great multi protocol module for your FrSky ACCST or ACCESS transmitter and Turnigy 9XR and 9XR Pro. This one multi protocol module will replace all of the different protocol 2.4Ghz Transmitter modules.

Also works with most transmitters that have a JR module bay and can provide a PPM signal to the module. The PPM firmware can be downloaded from github.

This module has a USB port for easy firmware upgrades. Just download Flash Multi V0.6.1 from github and follow the setup instructions.

These modules have been updated to firmware version V1.3.3.7 AETR or higher for use with OpenTx V2.3.9 or higher in serial mode.

Works best with the latest firmware OpenTx V2.3.12. or higher.

For best results with your Turnigy 9XR Pro you need to upgrade the ersky9x firmware to R223A6. Just go to "erskyTx test versions" to download the firmware. The latest module firmware V1.3.3.7 or higher works great with both of the latest versions of OpenTx and erskyTX.

Manual and data download:

http://pan.baidu.com/s/1bokfOjt


Working parameters:

Working voltage: 5-14 volts Working current: <=100mA

Working frequency: 2.4G ISM band RF power: +22dBm

Main control chip: STM32F103CBT6 (128K ROM, 20K RAM)

Size: 55x41x7mm, without buttons Net weight: 23g, with antenna

The tuner has two working modes: PPM mode and serial port mode.

In PPM mode, there are 31 different protocols corresponding to the 16 positions of the rotary coding switch (protocol 0 is reserved for serial port mode). Please refer to the list on the previous page of the manual for the correspondence between the two.

When the green light is off, you can use the knob to select protocols No. 1 to 15, and when the green light is on, you can select protocols No. 16 to 31.

If you need to turn on or turn off the green light, please follow the steps below:

Turn off the remote control, point the rotary coding switch to "0", press and hold the black link button on the tuner, then turn on the remote control, release the button after 3 seconds, and then you can see the green light switch between on and off , The optional protocol will be switched at the same time.

In PPM mode, normal use operation:

1. Fix the tuner, install the antenna, and turn on the PPM signal output on the remote control

2. According to the following default protocol list and your receiver type, point the tuner knob (the end of the handle with the vertical groove) to the corresponding gear.

3. When the linking has been completed, turn on the power switch of the remote control, the red indicator light on the tuner will always be on, and then the tuner will start to work normally, and then turn on your receiver (or airplane).

4. The tuner cannot switch the protocol during normal use. If you need to switch the protocol, please turn off the power first, adjust the knob, select the desired protocol, and then power on again.

5. If there is no valid PPM signal input, the red light will flash slowly.

In PPM mode, linking operation:
1. Turn on your receiver (or airplane) and follow the instructions of the receiver to enter the linking mode.

2. Press and hold the black link button on the tuner, turn on the remote control and wait to enter the system interface. After 3 seconds, release the link button, you can see the red indicator flashes quickly, indicating that the tuner enters the link mode. When the linking is over, the red light is always on.

3. Some protocols (for example: S-FHSS) do not need to operate on the tuner for linking, and for some protocols (for example: hubsan, e010), the tuner will automatically link to the frequency as soon as the tuner is turned on. .

Operation in serial mode:

When the green light is off and the knob on the tuner points to "0", the tuner can enter the serial port mode. In the serial port mode, all existing protocols can be used. The tuner protocol switching and frequency-linking operations can be done through the remote control. The menu is implemented, but only the remote control using er9X/erSky9X or OpenTX open source firmware can use the serial port mode. In addition, your remote control firmware also needs to be upgraded to the latest version.


For related information, see:
https://github.com/pascallanger/DIY-Multiprotocol-TX-Module

About the tuner firmware upgrade:

There are two jumper caps attached, do not short-circuit it in normal use, and short-circuit it according to the situation when upgrading the firmware.

The tuner can upgrade the firmware in two ways, a USB serial cable or a Micro USB cable (that is, a common Android phone data cable). The USB serial port method is relatively simple, so some general users recommend to equip it with a USB serial cable to upgrade.

For related information, see:
https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/docs/Compiling_STM32.md

Pacakge Content

1 X multi protocol module