SPECIFICATIONS

Introducition:

The Raspberry Pi Pico is a microcontroller board based on the Raspberry Pi RP2040 microcontroller chip. It has been designed to be a low-cost, high-performance microcontroller board with flexible digital interfaces. The Raspberry Pi Pico features two ARM Cortex-M0+ cores run up to 133MHz; 256KB RAM; 30 GPIO pins; and a broad range of interfacing options. This is paired with 2MB of onboard QSPI Flash memory for code and data storage.

In addition to powerful hardware resources, Pico has rich and complete software support and community resources. It comes with a complete Rasberry Pi official C/C++ SDK, Micropython SDK. Just click "https://pico.raspberrypi.org/getting-started" to get started with Raspberry Pi Pico.

Pico has been designed to use either soldered 0.1" pin-headers (it is one 0.1" pitch wider than a standard 40-pin DIP package) or can be used as a surface-mountable 'module', as the user IO pins are also castellated. There are SMT pads underneath the USB connector and BOOTSEL button, which allow these signals to be accessed if used as a reflow soldered SMT module.

Specification:

• RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom

• Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz

• 264KB of SRAM, and 2MB of on-board Flash memory

• Castellated module allows soldering direct to carrier boards

• USB 1.1 with device and host support

• Low-power sleep and dormant modes

• Drag-and-drop programming using mass storage over USB

• 26 × multi-function GPIO pins

• 2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels

• Accurate clock and timer on-chip

• Temperature sensor

• Accelerated floating-point libraries on-chip

• 8 × Programmable I/O (PIO) state machines for custom peripheral support

Product description

RP2040 Microprocessor (MCU) integrates dual-core ARM architecture Cotex-MO+ core, directly integrates 264KB RAM, supports up to 16M QSPI external expansion Flash, highly flexible I/O settings, including l2C, SPI, PIO ( Programmable I/O); YD-RP2040 core board is a core board circuit board made of RP2040 microprocessor (MCU), which is convenient for users to carry out peripheral expansion, circuit design and construction. Raspberry Pi has also launched its own official RP2040 core board, the model is Raspberry Pi Pico core board, YD-RP2040 core board, which can achieve no recognition result with Ra core in terms of mechanical size and electrical pins. The board is compatible for use, see the information for details on the differences, and improve a series of deficiencies of the Raspberry PiPico core board:

●Increased the PWR power indicator to improve the human-computer interaction experience when plugged into the USB power supply.

●Change the microUSB interface of Raspberry Pi Pico to Type-C of YD-RP2040 core board, the USB interface is convenient for users to find related USB cables more conveniently.

●Add a reset button, which is convenient for users to reset and update firmware in the power-on state.

●Add USRkey user button, which is convenient for users to verify and use simple input functions.

●Added RGB light group, which is convenient for users to operate the RGB light group to reflect various information through the on-off and brightness of red, green and blue lights.

Pin introduction：

Hardware introduction：

Update firmware operation process

■Press and hold the BOOT button on the board, do not release it, keep pressing it; first, connect the computer and the core board with the USB cable of the type-C interface.

■Press and hold the BOOT button on the board, do not release it, keep pressing it;

Press the RST button again;

■Release the BOOT button after 1 second;

The computer will be automatically recognized as a removable hard disk;

■Copy the file to be downloaded (burned) to the removable hard disk that appears, and the core board will restart automatically.

Lite Purple 16M

Product description:

RaspberryPi Pico is a low-cost, high-performance microcontroller development board with a flexible digital interface. In terms of hardware, the RP2040 microcontroller chip independently developed by Raspberry Pi is used, equipped with an ARM Cortex MO + dual-core processor, up to 133MHz operating frequency, built-in 264KB of SRAM and 2MB of memory, and there are up to 26 onboard Multi-function GPIO pins. In the software, you can choose the C/C++ SDK provided by the Raspberry Pi, or use MicroPython for development, and complete development materials and tutorials are provided, which can facilitate quick start development and embed it into the product.

The main features are:

1. Using Raspberry Pi official self-designed RP2040 microcontroller chip

2. Equipped with dual-core ARM Cortex M0+ processor, operating frequency up to 133MHz flexible clock

3. Built-in 264KB of SRAM and 16MB of on-chip Flash

4. USB1.1 host and device support

5. Support low-power sleep and hibernation mode

6. Can be identified as mass storage through USB for drag-and-drop download of programs

7. Up to 30 multi-function GPIO pins

8. 2 SPI, 2 12C, 2 UART, 4 12-bit ADC, 16 controllable PWM channels

9. Precise on-chip clock and timer

10. Temperature sensor

11. On-chip accelerated floating point library

12. 8 programmable I/0 (PIO) state machines for custom peripheral support

13. MicroPython firmware has been burned, you can directly use MicroPython for development