SPECIFICATIONS

Stepper Motor Driver Controller TB6600 0.2-5A CNC Engraving Machine HY-DIV268N-5A Stepper Motor 12 ~ 48V

Two-phase hybrid stepping motor dynamic
voltage 12 to 48V, the current is less than 5A outer diameter of 35 to 86 mm.
This drive using the drive's current loop subdivision control, the motor torque
ripple is very small, low-speed running is very smooth, almost no vibration and
noise. High-speed torque is much higher than other two-phase drive, high
positioning accuracy. Widely used in the engraving machine, CNC machine tools,
packaging machinery and other high resolution requirements on the device.

The main features

- average current control, two-phase
sinusoidal current drive output

- DC 12 ~ 48V power supply, the internal
integration of 12V and 5V regulator

- optically isolated signal input / output

- overvoltage, undervoltage, overcurrent,
and white short-circuit protection

- The input current of 1 to 5 amps, select
the drive a stepper motor.

- Output current of 0.2A ~ 5A

- Temperature Operating Temperature -10 to
45 C; Storage temperature -40 C to 70 C

- Humidity not condensing, not drops

- Gas prohibit combustible gas and
conductive dust

- Weight 200 grams

Control signal interface

- Figure 1 is a wiring schematic of the
drive

- 1, the definition of control signals

PUL +: step pulse signal is input side or
the positive pulse signal input positive terminal

PUL-: the negative input of the negative
input pulse signal or a positive pulse signal

DIR +: stepping direction signal input to
the positive terminal or negative pulse signal input to the positive terminal

DIR -: stepping direction signal input of
the negative side or reverse step pulse signal input negative terminal

EN +: offline can reset signal input side
is

EN-: offline can reset signal input
negative terminal

Offline enable signal is active, reset
drive failure to prohibit any pulse, the output of the drive

Power component is turned off, the motor
holding torque.

- Control signal connections

- PC control signal can be high, also can
be low effective. When active high, the control signal

- The negative side together as a signal to
active low, positive side of all control signals together as a signal common.

- For example, open-collector and PNP
output interface circuit diagram is as follows:

- Note: the VCC is 5V, R short

- VCC value of 12V, R 1K, more than 1/8W
resistor;

- VCC value of 24V, R 2K, more than 1/8W
resistor;

- Set the motor per revolution steps

The drive to set the number of steps per
motor revolution is 200 (whole step), 400 (2 segments), 1600 (8 segments), 3200
steps (16 segments).

The user can drive the front panel DIP
switch SW3 is SW4 bit of the drive to set the number of steps (such as Table 1)

Table 1

- Set the output phase current

- To drive torque stepper motor, the user
can drive panel DIP switch

- SW1, SW2 is to set the drive output phase
current (RMS) unit amperes, the switch position

- Corresponding to the output current,
output current value corresponding different types of drive. Concrete are shown
in Table 2.

- Output Current (A

Table 2

Current setting

- The semi-flow function is a step pulse
200ms, the driver output current is automatically reduced to the rated output
current50%, used to prevent motor heating.

Fourth, the power interface

- 1, DC +, DC-: to connect the drive power

- DC +: DC power level, power supply
voltage DC 12 to 48V. The maximum current is 5A. The

DC-: DC power supply negative level.

2, A + A-B + B-: to connect the two-phase
hybrid stepping motor

Drive and two-phase hybrid stepper motor's
connection with the four-wire system, the motor windings in parallel and series
connection, and connection method, high-speed performance, but the drive
current is large (for motor winding current of 1.73 times), Connected in series
when the drive current is equal to the motor winding current.

Five, the installation

- Around to have 20mm of space, can not be
placed next to the other heating equipment, to avoid dust, oil mist,

Corrosive gases, high humidity is too big
and strong vibration. +

Figure 3.

Six fault diagnosis

1, the status light indicates

RUN: green light in the normal work.

ERR: red light, power, light, power
indicator